Just How to Install a Bathtub in Your Bathroom
Just How to Install a Bathtub in Your Bathroom
Blog Article
They are making several good pointers regarding A Step-by-Step Guide to Installing a Bathtub overall in the article followed below.

Mounting a bathtub isn't precisely brain surgery, but it does need strong plumbing, woodworking, and often, tiling abilities. Replacing an old tub with a new one is likewise a reasonably difficult project. If the old bathtub is conveniently accessible, the job can move immediately; if you need to open up a wall surface to remove the old bathtub and position the brand-new bathtub, the task is a lot harder. In either situation, the job is within a residence handyman's skills, although you will need a helper to vacate the old bathtub and also set in the new one. Make certain you have actually qualified yourself for the job and are comfortable trying it. Rather than employing a professional to take control of a halfway-completed task, it is far better to consider employing one before you begin. Possibilities are you may need a professional plumber to make tube connections.
This short article will assist you set up a brand-new tub in your shower room if you have actually currently acquired a brand-new bathtub and also do not require to transform the plan of your previous water pipes.
Your tools as well as material checklist ought to comprise the following:
Removing Old Touches
If you require to change old taps with new ones as a part of your installation, then the first thing you must do is separate the water system. After doing so, switch on the taps to drain pipes any kind of water staying in the system. The process of removing the existing faucets can be rather troublesome due to the limited gain access to that is typically the situation.
Utilize a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipelines to the faucets. Have a fabric ready for the continuing to be water that will certainly originate from the pipelines. When the supply pipes have actually been gotten rid of, utilize the same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary faucets from turning during this procedure. When the taps have been gotten rid of, the holes in the bath/basin will certainly need to be cleaned up of any type of old securing substance.
Before carrying on to fit the brand-new taps, contrast the pipeline connections on the old faucets to the brand-new taps. If the old faucets are longer than the brand-new taps, after that a shank adapter is required for the brand-new taps to fit.
Suitable New Taps
If the tails of the new faucets are plastic, then you will require a plastic port to avoid damage to the thread. One end of the connector fits on the plastic tail of the tap and also the various other end supplies a link to the existing supply pipes.
If you need to fit a monobloc, after that you will certainly need minimizing couplers, which connects the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next off, position the faucet in the mounting opening in the bath/basin making sure that the washers remain in location between the tap and also the sink. Protect the tap in place with the supplier given backnut. When the tap is firmly in place, the supply pipes can be attached to the tails of the taps. The taps can either be connected by utilizing corrugated copper piping or with typical tap connectors. The former kind must be connected to the faucet finishes first, tightening up just by hand. The supply pipes can later on be linked to the other end. Tighten up both ends with a spanner after both ends have been attached.
Setting up the Bathtub
Making use of the two wood boards under its feet, put the bath tub in the needed position. The wood boards are practical in evenly spreading out the weight of the tub over the location of the boards rather than concentrating all the weight onto 4 small factors.
The next objective is to make certain that the bathtub is leveled all round. This can be attained by inspecting the spirit level as well as adjusting the feet on the bath tub until the level checks out degree.
To set up faucets, fit the bottom of the outermost versatile faucet port to the proper supply pipeline by making a compression join; then do the very same for the other faucet.
Switch on the water supply as well as examine all joints as well as brand-new pipework for leaks and also tighten them if required. Fill the tub as well as likewise inspect the overflow outlet and also the typical electrical outlet for leaks.
Ultimately, fix the bath paneling as defined in the producer's instruction manual. Tiling and also sealing around the tub must wait up until the bath tub has been utilized at the very least when as this will settle it into its final setting.
Getting ready for the Setup
To start with, the sustaining structure provided with the bathroom needs to be fitted (if called for) according to the supplier's instructions. Next, fit the taps or mixer to the bathtub. When suitable the faucet block, it is necessary to make certain that if the faucet features a plastic washing machine, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is likewise practical to fit a sustaining plate under the faucets system to avoid stress on the tub.
Fit the versatile tap connectors to the bottom of the two faucets making use of 2 nuts and also olives (occasionally provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet via the hole in the bathroom. Utilize the nut supplied by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which must be fitted inside the bath. Make certain you use every one of the provided washers.
Attach the catch to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bathroom ought to currently prepare to be fitted in its final position.
Tiling Around the Bath tub
In the location where the bath satisfies the ceramic tile, it is necessary to secure the joins with a silicone rubber caulking. This is essential as the installation can move sufficient to split a rigid seal, creating the water to pass through the wall surface between the bathroom as well as the tiling, bring about issues with dampness and also possible leakages to the ceiling below.
You can pick from a range of coloured sealers to blend in your fixtures and also fittings. They are marketed in tubes and cartridges, and also are capable of securing gaps approximately a width of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with twists of drenched paper or soft rope. Keep in mind to constantly fill up the bath tub with water before securing, to enable the movement experienced when the tub remains in use. The sealer can fracture relatively very early if you do not take into consideration this movement prior to securing.
Additionally, ceramic coving or quadrant floor tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are also quickly available on the market. It is advisable to fit the ceramic tiles making use of water-resistant or water resistant adhesive and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

Do you really like reading up on How to Install a Bathtub Yourself? Try to leave feedback directly below. We will be glad to find out your responses about this blog posting. In hopes that you come back again before long. Loved our article? Please share it. Let somebody else find it. I truly appreciate reading our article about How to Install a Bathtub.
Browse Our Site Report this page